CGCXC - GRAY CONCRETE CRACK SEAL, 8640
- MSDS: CGCXC
- Manufacturer: QUIKRETE COMPANIES
- Product Name: GRAY CONCRETE CRACK SEAL, 8640
- National Stock Number: 5610-00N082431
Product Identification
Product ID:GRAY CONCRETE CRACK SEAL, 8640
MSDS Date:07/15/1996
FSC:5610
NIIN:00N082431
MSDS Number: CGCXC
Responsible Party
ATLANTA, GA 30329
US
Emergency Phone: 770-216-9580
Info Phone: 770-216-9580
Cage: IO174
Contractor
Telephone: 404-634-9100
Cage: IO174
Ingredients
ACRYLIC POLYMER
CAS: 25068-63-7
OSHA PEL N/K
ACGIH TLV: N/K
1,2-PROPANEDIOL; (PROPYLENE GLYCOL)
CAS: 57-55-6
RTECS: TY2000000
OSHA PEL N/K
ACGIH TLV: N/K
CALCIUM CARBONATE; (LIMESTONE/MARBLE)
CAS: 1317-65-3
RTECS: EV9580000
OSHA PEL 15 MG/M3 TDUST
ACGIH TLV: 10 MG/M3 TDUST
PROPIONIC ACID, 2-METHYL-, MONOESTER
CAS: 25265-77-4
RTECS: UF6000000
OSHA PEL N/K
ACGIH TLV: N/K
IRON (III) OXIDE; (IRON OXIDE PIGMENTS)
CAS: 1309-37-1
RTECS: NO7400000
OSHA PEL 10 MG/M3 (FE)
ACGIH TLV: 5 MG/M3 FUME (FE)
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHALATION OF VAPOR OR MIST CAN CAUSE
FOLLOWING: HEADACHE, NAUSEA, IRRITATION OF NOSE, THROAT AND LUNGS.
EYE CONTACT:DIRECT CONTACT WITH MATERIAL CAN CAUSE IRRITATION AND
POSSIBLE CORNEAL INJURY. SKIN CONTACT:PROLONGED OR REPEATED
CONTACT CAN CAUSE SLIGHT IRRITATION.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:SKIN:THORO WASH AFFECTED AREA W/SOAP & WATER. REMOVE CONTAM
CLTHG. EYES:FLUSH W/LG AMTS OF WATER FOR AT LST 15 MINS, LIFTING
UPPER & LOWER LIDS OCCAS. GET MED ATTN. INGEST:GIVE 2 GLASSES OF
WATER. IF LG AMTS ARE INGESTED, INDUCE VOMIT W/IPECAC SYRUP/BY
PLACING FINGER AT BACK OF THROAT. NEVER GIVE ANYTHING BY MOUTH TO
UNCON PERS. GET MED ATTN. INHAL:REMOVE TO FRESH AIR IF EFTS OCCUR.
CONSULT MD.
Fire Fighting
Flash Point:248F,120C
Extinguishing Media:USE METHODS APPROPRIATE FOR SURROUNDING FIRE.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT .
Unusual Fire/Explosion Hazard:THIS WATER BASED DISPERSION CAN SPLATTER
AT TEMPS >100C(212F). POLYMER FILM CAN BURN ONCE WATER HAS EVAP.
PROD ALSO MAY CNTN <1% OF SOLV W/FL PT OF 120C(248F).
Accidental Release
Spill Release Procedures:KEEP SPECTATORS AWAY. FLOOR MAY BE SLIPPERY;
USE CARE TO AVOID FALLING. CNTN SPILLS IMMED W/INERT MATLS (E.G.
SAND, EARTH). TRANSFER LIQS & SOLID DIKING MATLS TO SEPARATE
SUITABLE CNTNRS FOR RECOVERY/ DISP. CAUT:KEEP SPILLS & CLEANING
RUNOFF OUT OF MUNICIPAL SEWERS & OPEN BODIES OF WATER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:AVOID SKIN & EYE CONTACT & AVOID
BREATHING VAPORS. KEEP FROM FREEZING; MATERIAL MAY COAGULATE.
Other Precautions:MINIMUN RECOMMENDED STORAGE TEMPERATURE FOR THIS
MATERIAL IS 1C (34F). MAXIMUM RECOMMENDED STORAGE TEMPERATURE FOR
THIS MATERIAL IS 49C (120F).
Exposure Controls
Respiratory Protection:NIOSH APPROVED RESPIRATOR APPROPRIATE FOR
EXPOSURE OF CONCERN .
Ventilation:USE LOC EXHST VENT W/MIN CAPTURE VELOCITY OF 100 FT/MIN (30
M/MIN) AT POINT OF VAP EVOLUTION. REFER TO CURRENT EDITION OF
"INDUSTRIAL VENT:A MANUAL OF (SUPDAT)
Protective Gloves:NEOPRENE GLOVES. GLOVES OF OTHER CHEM RESIST MATLS
MAY NOT PROVIDE ADEQ PROT.
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:EYE WASH FOUNTAIN & DELUGE SHOWER WHICH MEET
ANSI DESIGN CRITERIA .
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
VENTILATION: REC PRACTICE" PUBLISHED BY ACGIH FOR INFO ON DESIGN,
INSTALLATION, USE & MAINT OF EXHST SYSTEMS.
Chemical Properties
Boiling Pt:B.P. Text:212F,100C
Melt/Freeze Pt:M.P/F.P Text:30.0F,-1.1C
Solubility in Water:DILUTABLE
Appearance and Odor:GRAY VISCOUS LIQUID W/SLIGHT ETHER & AMMONIA ODOR.
Stability
Stability Indicator/Materials to Avoid:YES
AVOID CONTACT W/STRONG OXIDIZING AGENTS OR STRONG ALKALIES.
Stability Condition to Avoid:AVOID TEMPERATURES >177C (350F), ONSET OF
POLYMER DECOMPOSITION. THERMAL DECOMP IS DEPENDENT ON TIME &
TEMPERATURE.
Hazardous Decomposition Products:THERMAL DECOMPOSITION MAY YIELD
ACRYLIC MONOMERS.
Disposal
Waste Disposal Methods:COAGULATE EMULSION BY STEPWISE ADDITION OF
FERRIC CHLORIDE & LIME. REMOVE CLEAR SUPERNATANT & FLUSH TO
CHEMICAL SEWER. INCINERATE LIQUID & CONTAMINATED SOLIDS I/A/W
LOCAL, STATE & FEDERAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.